English
简体中文
Русский язык
Français
日本語
한국어
Português
Español
Website navigation
Position:
Leave A Message
E-mail:
Tell:
Whatapp:
Address:Room 1505, Building 9, No. 26 Dongqing Street, Zhengzhou High-tech Industrial Development Zone
Tel Number
180-3717-8440
The main purpose:
The design of this three-temperature zone automatic feeding and discharging Rotary Tilt Tube furnace is mainly to coat the conductive layer on the cathode material of lithium ion battery (such as LiFePO3, LiMnNiO3), and can also prepare Si/C anode material by CVD.
Product description:
The three-temperature zone automatic feeding and discharging Rotary Tilt Tube furnace is equipped with an automatic feeder and a receiving tank. The powder can be automatically and quantitatively fed into the furnace tube. This process can be carried out in a protective atmosphere environment, and the continuous CVD method can be used to coat and modify the powder material. The receiving tank can collect the processed powder under the atmosphere protection environment.
Technical Parameter:
Optional configuration: The furnace can be equipped with communication interface and software, which can directly control various parameters of the furnace through the computer, and can observe the PV and SV temperature values on the furnace and the operation of the instrument from the computer. It can be drawn in real time, and the temperature data at each moment can be saved, which can be recalled at any time.
Precautions:
1. When the furnace temperature of the equipment is greater than or equal to 200 °C, it is forbidden to open the furnace to avoid injury;
2. When the equipment is in use, the pressure in the furnace tube shall not exceed 0.02MPa (absolute pressure) to prevent equipment damage caused by excessive pressure;
3. When the temperature of the furnace body is higher than 1000°C, the furnace tube cannot be in a vacuum state, and the air pressure in the furnace tube must be equal to the atmospheric pressure and kept at normal pressure;
4. When heating the sample, it is not recommended to close the exhaust valve and the intake valve at the flange end of the furnace tube. If you need to close the gas valve to heat the sample, you should always pay attention to the reading of the pressure gauge. The reading of the absolute pressure gauge should not be greater than 0.02MPa. The exhaust valve must be opened immediately to prevent accidents (such as furnace tube rupture, flange flying out Wait).
The design of this three-temperature zone automatic feeding and discharging Rotary Tilt Tube furnace is mainly to coat the conductive layer on the cathode material of lithium ion battery (such as LiFePO3, LiMnNiO3), and can also prepare Si/C anode material by CVD.
Product description:
The three-temperature zone automatic feeding and discharging Rotary Tilt Tube furnace is equipped with an automatic feeder and a receiving tank. The powder can be automatically and quantitatively fed into the furnace tube. This process can be carried out in a protective atmosphere environment, and the continuous CVD method can be used to coat and modify the powder material. The receiving tank can collect the processed powder under the atmosphere protection environment.
Technical Parameter:
| Model | KJ-T1000-R-Ⅲ-AF |
| Shell structure | Double shell with air cooling system |
| Furnace material | Furnace using alumina polycrystalline fiber |
| Furnace tube material | Metal tube (other materials are optional) |
| Furnace tube size approx. | φ80mm long about 2000mm |
| Heating zone | Three temperature zone heating |
| Maximum working temperature | 1000℃ |
| Temperature control method | Independent temperature control in three temperature zones, each temperature zone can realize intelligent 30-segment PID programmable control, with over-temperature protection function |
| Flange joint | Equipped with stainless steel vacuum flange with installed mechanical pressure gauge |
| Sealing system | The furnace tube and the flange are extruded and sealed by a silicone O-ring, which is convenient for disassembly and assembly, can be disassembled and assembled repeatedly, and has good air tightness. It can be evacuated and ventilated during the rotation process. |
| Heating rate | 0-10℃/min adjustable |
| Heating element | Electric resistance wire |
| Temperature measuring element | 3 N-type thermocouples, independent temperature control |
| Vacuum degree | Pre-evacuated to -0.1MPa (value of vacuum pressure gauge) |
| Automatic feeding and discharging device | Equipped with an automatic feeder and a receiving tank, which can feed the powder into the furnace tube in a certain proportion |
| Provide related accessories | Crucible tongs, high temperature gloves, thermocouples, furnace plugs, manuals, warranty cards, etc. |
| After-sales service | 12 months warranty, lifetime warranty (except wearing parts) |
| More specifications can be customized on request | |
Optional configuration: The furnace can be equipped with communication interface and software, which can directly control various parameters of the furnace through the computer, and can observe the PV and SV temperature values on the furnace and the operation of the instrument from the computer. It can be drawn in real time, and the temperature data at each moment can be saved, which can be recalled at any time.
Precautions:
1. When the furnace temperature of the equipment is greater than or equal to 200 °C, it is forbidden to open the furnace to avoid injury;
2. When the equipment is in use, the pressure in the furnace tube shall not exceed 0.02MPa (absolute pressure) to prevent equipment damage caused by excessive pressure;
3. When the temperature of the furnace body is higher than 1000°C, the furnace tube cannot be in a vacuum state, and the air pressure in the furnace tube must be equal to the atmospheric pressure and kept at normal pressure;
4. When heating the sample, it is not recommended to close the exhaust valve and the intake valve at the flange end of the furnace tube. If you need to close the gas valve to heat the sample, you should always pay attention to the reading of the pressure gauge. The reading of the absolute pressure gauge should not be greater than 0.02MPa. The exhaust valve must be opened immediately to prevent accidents (such as furnace tube rupture, flange flying out Wait).
